|
Leveraging Technology Solutions for Safe and Efficient Operations
EMAS Energy Services have a high specification modern equipment fleet meeting international standards. The equipment is specifically designed to meet the challenges and limitations of Asia Pacific's small offshore platforms as well as the international market demands.
- Workover (WO) and Drilling Units
- Pumps
- Tanks
- Accommodation, Vessels and Other Equipment
 Brochure for download |
|
- 400 type self-propelled special oil field design workover rig
- Rated hook load: 600 kN (135,000 lbs)
- Max hook load: 900kN (202500 lbs)
- Servicing depth: 4,000m (13,120 ft) using 2 1/8 EUE tubing with 10 x 8 carrier driving type
- Power package adapted to Detroit diesel engine and Allison transmission
- Equipped with 2 tow drums to draw work
- 1x bailing drum wire line storage capacity: 4,200m (13,776 feet), 1 1/6 diameter
- Telescoping derrick height: 31.6 m or 103,648 ft
- Adapted square pipe welding structure with racking platform and rod basket
- Carrier load has rational distribution, good for driving cross country
- Enough space for operating and servicing all core assembles
- Good resistance to wind, sand and vibration
- Environmental temperature : -20 to 45 °C (-4 to 113 °F)
- Standard main power package and hydraulic components (e.g oil seal and bearings)
|
|
Brochure for download |
|
- Diesel powered
- Lifting capability: 340,000
- Capable of all drilling, workover and snubbing operations for conventional draw work type Rigs.
- Hydraulically movement of tubular components in wellbore.
Small operational footprint but powerful rig.
- All pipe movement via dual counterbalanced winch set-up and pipe slide eliminating all unnecessary safety risks.
|
|
Brochure for download |
|
- Zone 2 diesel powered unit
- Lifting capability: 460 000lbs
- X,Y skiddable base
- 10 000 of 3 ½ drillpipe can be racked vertically
- 20 000ft/lb rotary head
- 4 ton SWL gin pole
- Built in access ladders
- No guy wires required
|
|
Brochure for download |
|
- Specialized rack and pinion mast-type 250K UB Rigs rig
- Lifting capacity: workover rig 250,000 lbs, snubbing rig 125,000lbs
- Self-contained unit capable of all conventional underbalanced drilling, milling, workover and snubbing operations but operating at greater depths.
- Able to efficiently mill out composite bridge plugs in an under-PLC electronic-over-hydraulic operating systems.
- Safe automated tripping procedure increases tubular insertion/removal speed
- 24m mast allows for multiple BPO configurations to be added, while maintaining standard drilling and tripping capabilities.
- Simple and quick installation of BOPs reduces rig set-up time, costs, and increases safety.
- Similar footprint to conventional service rigs allows operations in tighter locations with reduced land disturbance.
|
|
Brochure for download |
|
- Designed and manufactured for advanced performance, reliable operation, convenient mobilization, economic operations and meeting HSE requirements.
- Performance and quality beyond advanced international levels of similar drilling rigs.
- Rig layout meets requirements for helicopter hoisting, with assembly by an on-site crane.
|
|
Brochure for download |
|
The EMAS 3, (600k) Technical Data- 22 overall height
- Lower Workbasket
- Lift Capacity 600,000 lbs
- Snub Capacity 300,000 lbs
- Hydraulic Jack w/ 12 stroke
- Built in 2 5,000 psi Stand Pipe
- 10,000 ft/lb Rotary Table with Lock
- All Pipe handling equipment 3 1/2 to 5 1/2 inclusive
- 4 sets 400K Type F Slip Bowls (2 3/8-8 5/8 and 11 Full Bore capability)
- Workbasket w/ winch panel and unit operating controls all PLC (electronic/ hydraulic)
- 5 1/2 Phoenix Tongs w/ hydraulic backup (2 7/8-5 1/2 capability)
|
|
Brochure for download |
|
- Dimension: 610mm (B) 711mm (L) 737mm (H)
- Weight: 112 kg
- Lifting/ Transport: Transportation on pallet
- Type: Hydratron DHDA 33
- P Max.: 464 bar (6728 psi)
- Q Max.: 31,7 litre/min (with 7 bar (100 psi) air supply and pressure less system)
- P/Q (with 7 bar air-supply): 0 bar 31,7 litre/min
206 bar 15,8 litre/min
414 bar 6,6 litre/min
- Connection Water In: 1 ea. 1" Offshore claw coupling
- Connection Water Out: 1 ea. 1/4 BSP Male
- Connection Air: 1 ea. 1" Offshore claw coupling
- Filter Water In: Washable strainer
- Other Information: Can be used with water, hydraulic and some type of chemicals
|
|
Brochure for download |
|
- Diesel Engine: JCB, 444 Diesel Max / PP 854
- Area Classification: Pyroban Zone II, system, API RP500 Class 1, Div 2, Group G, T3 (200 Deg)
- Safety Shutdowns: Full set
- Power Rating: 56.7Kw @ 2200rpm
- Compression Ratio: 18.6:1
- Direction of Rotation: Clockwise
- Combustion Cycle: 4 stroke
- Sound Proof Feature: To be fitted
- Full unit specification supplied upon request
|
|
Brochure for download |
|
- 5 bbl/min Franklin motor
- Stainless steel housing
- Discharge head 37 meters at 2850 rpm
- 15 hp and 4 discharge hose
|
|
Brochure for download |
|
A Team of Industry Leaders in Packaged Horizontal Pumping Technology
EMAS Energy Services have engaged the services of a quality manufacturer of these Horizontal Pumping Systems to address a gap in the market in the Asia Pacific region for low maintenance continuous pumping systems. EMAS recognize that this type of pumping system mitigates the need for bulky diesel triplex pumping spreads which also require a sizeable pumping crew.
- Performance and quality beyond advanced international levels of similar drilling rigs.
- Rig layout meets requirements for helicopter hoisting, with assembly by an on-site crane.
- Pipeline boost
- Hydraulic motive power
- Industrial fluid transfer
- Numerous other applications
- CO2/LNG booster services
|
|
Brochure for download |
|
- Length: 6.4 meters / 21.0 ft
- Width: 2.5 meters / 8.0 ft
- Height: 3.1 meters / 10.0 ft
- Weight: 12,000 kg
- Treating Iron: 450 ft of 2 Figure 1502 H2S & NACE certified 10,000 psi CWP treating irons
|
|
Brochure for download |
|
- Zone 2, DNV 2.7.1 split skid
- 600HP triplex pumps
- Built in flow meter
- Drip pan and fuel tank
- Sound attenuated 10 000psi pump up to 8 bbl/min
|
|
Brochure for download |
|
- Design: Oilfield Service
- Volume: 150 Barrels
- Pump Drive: Electric 50Hz 4 core cable
- Outlets: 2” c/w butterfly valve
- Pump: 3”x2”x13” Centrifugal
- Fill Up Line Connections: 2” Fig 1502
- Sight Glasses: 1” c/w shut off valves and recessed into tank wall
- Ladder: Attached to the tank c/w non slip covering
- Lift Points: Four
- Slings: Four point lifting with master link
- Vented: Yes, inverted U tube
- Bund: Yes, around C pump area
Dimensions
- Length 6.05 meters / 9.2 ft
- Width 2.45 meters / 9 ft
- Height 3.07 meters / 9.3 ft
- Weight 7,000 kg Full
|
|
Brochure for download |
|
- Dimension : 290 x 510 x300 cms. MGW 4 tons.
- Enclosed tank with 2" venting line, 4" fill up line, 4" suction line, 4" overflow line.
- Capacity 160 bbl two partitions (80 bbl/ Partition)
- Overflow line is connected to both partitions to prevent to prevent over filling the tank to balloon due to pressure trap prior tank full with fluid. The over flow line will allow the fluid flow out from the tank once fluid level up to 140bbl.
- There are two suction outlets to the triplex pumps to increase the suction flow rate to prevent the suction line vibrating and to increase the pump output efficiency.
- There is fluid level air alarm sensor installed on the tank. The alarm will activate once the fluid level is up to 3/4 of tank capacity.
- One way air flow valve installed on top of both partition to prevent tank collapse if the venting line, over flow line plugs or has been closed during the pumping operation.
|
|
Brochure for download |
|
- Design: Emas Energy Services
- Manufacturer: Thai Oilfield Machinery Services
- Volume: 200 Barrels
- Mixing: Stainless steel hopper on return jet shearing line c/w 4 valve
- Bottom Outlets: 4 butterfly valve, one for each compartment and manifold
- Suction connections: 4 Fig 206
- Return side connections: 4 Fig 206
- Compartment return lines: 4 Butterfly valves
- Sight glasses: 1 c/w shut off valves and recessed into tank wall
- Ladder: Recessed in to tank wall c/w non slip covering
- Handrail: Drop down design permanently installed
- Lift points: DNV 2.7.1 designed
- Slings: Four point lifting with master link
- Vented: Open top design c/w access hatches for return line valves
Dimensions
- Length: 6.09 meters / 20.0 ft
- Width: 2.4 meters / 8 ft
- Height: 2.6 meters / 8.5 ft
- Weight: 7,000 kg Empty
|
|
Brochure for download |
|
- Design: Emas Energy Services
- Manufacturer: Thai Oilfield Machinery Services
- Volume: 70 Barrels
- Mixing: N/A
- Bottom Outlets: 4" Butterfly valve, one for each compartment and manifold
- Suction Connections: 4" Fig 206
- Fill Up Line Connections: 2" Fig 1502
- Compartment Return Lines: N/A
- Sight Glasses: 1 c/w shut off valves and recessed into tank wall
- Ladder: Attached to the frame and c/w non slip covering
- Handrail: Drop down design permanently installed
- Lift Points: DNV 2.7.1 designed
- Slings: Four point lifting with master link
- Vented: N/A
|
|
Brochure for download |
|
- Compact Size: Small fixture and easy placement.
- Heat Dissipation: Multi side heat exchanging fins for efficient thermal transfer.
- Water/Dust Proof: Two piece hinge and gasket provided on the flange cover to protect against the ingress of dust or fluid.
|
|
|
Brochure for download |
|
- 1 x Master Remote Panel c/w 3 x Read Back Pressure Gauges and Facitlity to operate all
- Functions and Annular Regulator
- 1 x MINI REMOTE PANEL: c/w 3 x Read Back Pressure Gauges and Facility to operate all
- Functions Including Annular Regulator
- 2 x 24 Line Air Control Bundle x 150 ft Long
|
|
Brochure for download |
|
- Length 3.04 meters / 10 ft
- Width 2.44 meters / 8 ft
- Height 2.44 meters / 8 ft
- Weight 7,000 kg
|
|
Brochure for download |
|
- Classification/Certification: ABS + A 1 + AMS Self Elevating Unit. Lift Boat. Meets regulations for USCG, ABS, IMO.
- Length Overall: 56.4 m
- Beam Moulded: 44.2 m
- Depth Moulded: 6.9m
- Summer Draft Moulded: 3.5m
- Leg Length: 96m
- Leg Diameter: 3.1 m
- Maximum Water Depth: 65m
- GRT: < 3000 MT
- Speed: Approximately 6 knots
- Helideck Rated: Suitable for Sikorsky S-92 helicopter
- Azimuth Propulsion: 3 x azimuth thrusters, 1100kW @ 690V/3Ph/60Hz
- Electric Power Generator: 4 x Caterpillar model 35 168,1285 kW @1200 rpm
- Emergency Generator: 1 x Caterpillar model C4.4 DITA, 95ekW @ 1800 rpm
- Self-elevating Power Units: 9 x 300HP hydraulic motor, three for each leg coupled to variable displacement pressure compensated pumps.
- Self-elevating Gear Units: 54 pinion drive gear units per liftboat, each gear 80 MT lifting capacity
- Bow Thruster: 1 x transverse FPP bow thruster, 440kW @ 690V/3Ph/60Hz
- Steering System: Electric/hydraulic steering, with 2 stations
- Fuel Oil Tank Capacity: 320 MT
- Water Tank Capacity: 150 MT
- Accommodation: 160 persons
- Ancillary Equipment: 2 x 120' LEC500 cranes, 243 MT @ 9.14m, 208 MT at 10.7m, 101 MT @21.23m, API
- Load During Jack·up: 680 MT
- Deck Space: Approximately 15,410 ft2
|
|
Brochure for download |
|
- Model: Super C, Model D and Goliath
- Manufacturer: Wachs
- Super 'C' Tubular Range: 2" - 12"
- Model 'D' Tubular Range: 6" - 18"
- Goliath Tubular Range: 16" - 32"
- Area of Operation: Surface and Sub Sea
- Power Units: Rated for Offshore Use
- Horse Power: 23 - 46 Hp
- Hydraulic Fluid Flow Rate: 53 l - 61 l/min
- Pressure Rating: 1600 psi - 2000 psi
- Starting System: Pneumatic
- Wall Thickness Cutting Range: Any
- Solids Cutting: Yes
- Cutting Speed: All Sizes 1" per minute
- Feed System: Automatic
- Clamping System: Hydraulic
- Operating Control: Stainless Steel Remote Panel
- Hole Saw Size: 3"
- Lifting Pins: Full range to suit all tubular sizes
- Lifting Plates SWL: Up to 20 ton
- Hole Saw Feed: Automatic
- Length: 3.05 meters / 10 ft
- Width: 2.44 meters / 8.0 ft
- Height: 1.3 meters / 4.0 ft
- Weight: 3,500 kg
|
|
|
| |
RELATED LINKS
For more information, please contact:
Mr Bob Davidson, Operations Director
Tel: +66 (0) 2792 9599
Email:
Address: Olympia Thai Tower, 5th Floor, Ratchadapisek Road, Samsennok, Huay Kwang, Bangkok, Thailand, 10310
|
